Audio Pull-Up

Audio pull-up adjusts audio speed to stay in sync when video is converted between frame rates, such as 23.976 and 24 fps.

In this article

Related Terms

Start Video editing now

What is Audio Pull-Up?

Audio pull-up fixes a specific problem that comes up when you change between certain frame rates. It matters most for:

  • 23.976 fps to 24 fps. These run at slightly different speeds, so the audio falls out of sync without a fix.
  • NTSC conversions. Frame rates of 29.97 fps and 30 fps are a little different, so the audio needs adjusting.
  • Mixed frame rate projects. When you combine footage shot at different frame rates, the audio needs handling.

Here is the heart of the problem:

  • Different frame rates run at slightly different speeds. For example, 24 fps is a touch faster than 23.976 fps.
  • Audio left at its original speed no longer lines up with video that has been sped up or slowed down.
  • Pull-up (or pull-down) nudges the audio to match the new video speed.

Pull-up and pull-down are two sides of the same fix:

  • Pull-up. Adjusts audio when you go from slower to faster, like 23.976 to 24 fps.
  • Pull-down. Adjusts audio when you go from faster to slower, like 24 to 23.976 fps.

Both terms just describe the audio tweak you need when the frame rate changes.

In most modern editing, your software handles pull-up and pull-down for you. It becomes something to watch for in specific cases, like cross-format projects, broadcast deliveries, and theatrical work.

Need editors who handle complex technical workflows?

Editors matched to your brand. Turnaround in as little as 24 hours.

Why audio pull-up matters

Here are a few reasons this adjustment matters.

It gives you flexibility. You can shoot at one frame rate and deliver at another, because the audio adjustment makes the switch possible.

It keeps NTSC content compatible. US broadcast uses NTSC frame rates, so projects that cross regions need the audio handled.

It bridges theatrical and broadcast. Theatrical work uses 24 fps, while broadcast uses 23.976 or 24p. Moving between them means matching the audio.

It keeps mixed projects clean. When you combine footage from different frame rates, you need the audio to stay consistent.

It keeps sound in sync. Without pull-up or pull-down, the audio slowly drifts away from the picture.

It is standard practice. Professional teams handle these conversions all the time.

For client work that involves different frame rates, it helps to know pull-up exists.

How audio pull-up is handled

Here is how it works in practice.

Spot when you need it. Compare your source frame rate to your target frame rate. The gap between them tells you whether pull-up is needed.

Use your software’s settings. Modern editing software handles most pull-up cases for you, as long as it is set up correctly.

Apply it during the conversion. The audio adjustment happens at the same time you change the frame rate.

Check the sync afterward. Once the conversion is done, make sure the audio still lines up with the picture.

Write down what you did. On complex projects, note what was converted and how.

For most client work, the automatic handling is enough. Only specific cases call for hands-on attention.

Practical considerations

A few things to keep in mind.

Match frame rates when you can. If you shoot at the rate you plan to deliver, you skip the conversion entirely.

It is mostly an NTSC thing. Pull-up issues show up most often in NTSC-based work.

Modern workflows have fewer issues. When everything stays progressive at the same frame rate, most of these problems go away.

It can change the audio a little. Pull-up makes small shifts in pitch and timing. They are minor, but they are there.

International work needs care. Projects that cross PAL and NTSC regions need the audio handled with attention.

For client work, pull-up only comes up now and then. Most projects never need you to think about it.

How Clipmasters Uses This

Audio pull-up is a small technical detail that your software usually handles for you, but it still helps to have an editor who knows when it matters. At Clipmasters, your editor can tell whether a sync issue comes from a frame rate conversion or something else, and fix it the right way. It is simply part of the edit, not something you need to manage yourself.

Frequently asked questions

When does audio pull-up apply?

It applies when you convert between certain frame rates, like 23.976 fps and 24 fps, or between NTSC frame rates. It comes up most often in cross-format work or when moving from theatrical to broadcast.

Is audio pull-up automatic in modern software?

Mostly, yes. Modern editing and audio software handles the common cases for you, as long as it is set up right. Knowing about it helps when something goes wrong or you need manual control.

Does pull-up affect audio quality?

Only a little. The pitch and timing shift slightly, usually about a 0.1% change for pull-down. Most listeners cannot hear the difference, and the audio quality stays essentially the same.

Can I avoid needing pull-up?

Yes. Match your production frame rate to your delivery frame rate, and there is no conversion to do. The trick is to decide on your frame rate early.

Does this apply to PAL content?

PAL runs at 25 fps, and converting between PAL and NTSC has its own audio considerations. The idea is the same, but the exact adjustments differ. International projects deal with PAL and NTSC handling all the time.

Loading video…